Can you hook up two speakers to one output

After working with the subwoofer and room that you have, if you find that you need, or want, more than one subwoofer, the question then becomes: how do i hook-up two, or more, subwoofers in my home theater system. How to use two speaker systems at once on your computer by mike venture surround sound can greatly enhance your multimedia experience, whether you're listening to music, playing computer games or watching movies most computers have a built-in ability to output multichannel audio without specialized equipment, so if you have two. As you can see, the two speakers are in “series” with the each other how to connect 2 speakers in parallel and series below is a table showing how to wire up two speakers in parallel and series for common scenarios.

Is it dangerous/ will it work to hook two sets of speakers into one output on my surround sound for example, i have 2 speakers i want to use for center, can i put both negatives and both positives in their respective holes and get sound from both. Multiple audio sources, one set of speakers tags: speakers audio solved anyway to set up my speakers to output audio for my pc, xbox one and my monitor solution 3 rca audio devices to one set of rca audio speakers solution solved controlling multiple sources for desktop speakers solution are there audio cable splitters/uniters that allow two devices to play on one set of speakers. I would like to hook the pair of small speakers above the tv to the center channel output on my integra receiver i know it might sound worse than having on center speaker, but i do not want to buy more speakers. While you can connect any number of speakers in series, try to keep the total equivalent-load impedance for each channel below 16 ohms, since most amps are not designed to handle higher loads figure 1a demonstrates how to wire a pair of speakers in series the positive output terminal from one channel of the amplifier is wired to.

Home entertainment how to hook up a subwoofer to a stereo system hint: you don't necessarily need a receiver with subwoofer output jacks. If you are having a party and want loud music outside, just make sure the workshop and lounge room are turned down – this reduces the total load and this effectively means only one or two pairs of speakers are connected to the amplifier.

If all of the speakers have a common impedance, you can simply divide the common impedance by the total number of speakers to get the net impedance examples: two 8 ohm speakers wired in parallel will have a net impedance of (8 divided by 2) 4 ohms. When two 8-ohm speakers are connected in parallel, the total impedance for the two speakers is 4 ohms the p3500s power amplifier can be used at 4 ohms, and the output power will increase with reduced impedance the benefits to connecting speakers in parallel are an increase in output compared to just using one speaker per stereo side, as well as the ability to angle the speakers.

However, you can install an impedance matching speaker selector switch to toggle one pair of the speakers off and leave just one pair playing to attach 4 speakers to a single connect:amp, the speaker impedance must be 8 ohms anything outside of that may damage the connect:amp and speakers.

  • Make sure that wherever you choose to place your speakers, the connector cable will reach its corresponding input on your computer, and the power cable (if you have one) can.
  • When the switch is set to stereo, each jack connects to a separate 8ω speaker and you use both jacks, one for the amp's left output and one for its right output to make a four-speaker mono/stereo cabinet, replace each 8ω speaker with either two 4ω speakers wired in series or two 16ω speakers wired in parallel the jack impedances will be.

Can i hook up 2 speakers to one port on home theater system you can connect 2 speakers to a single output of your receiver if the speakers load does not go below what the receiver says it can handle if the 2 speakers you are connecting each have an impedance of 4 ohms and you connect them in parallel. Connecting two sets into speakers a on the receiver and two pairs into speakers b on the receiver without any intervening volume controls would further mean all four pairs of speakers will be set at the same output level by the master volume control of the receiver it would be a very unusual installation where all four pairs of speakers.

Can you hook up two speakers to one output
Rated 5/5 based on 37 review